欧美日韩在线视频,欧美亚洲日本国产,97久久超碰日韩精品,天天干夜夜想

歡迎進入濟南濟柴環能燃?xì)獍l(fā)電設備有限公司官網！
當前位置：首頁 - 新聞中心 - 公司新聞

公司新聞

瓦斯發電瓦斯發電機組增壓器事項介紹

返回 2021.01.29 來源：http://www.vw95.cn 0
在使用瓦斯發電機組時，要注意增壓器的使用情況：
When using gas generator set, attention should be paid to the usage of supercharger
增壓器在高速、高溫、下工作，渦輪進口溫度可高達650°左右，標定轉速27500r/min，使用中特別注意做好維護保養工作。
The turbocharger works at high speed, high temperature and low temperature. The turbine inlet temperature can reach about 650 ° and the rated speed is 27500r / min. special attention should be paid to the maintenance work in use.
1.新啟用或維修后的增壓器，裝機前應用手撥動轉子檢查轉子轉動情況，正常情況下，轉子應輕快、靈活、無卡滯和異常聲響;
1. For the supercharger after new use or maintenance, the rotor should be manually moved to check the rotation of the rotor before installation. Under normal conditions, the rotor should be light, flexible, free of stagnation and abnormal sound;
瓦斯發電機組
2.接好潤滑管路，保持潤滑油路暢通，采用浮動軸承，對潤滑油要求較高，正常工作時，機油壓力應保持在300-500kPa之間，發動機怠速時，增壓器的進油壓力應不低于80kPa;
2. Connect the lubricating pipeline, keep the lubricating oil pipeline unblocked, adopt floating bearing, and have higher requirements for lubricating oil. During normal operation, the oil pressure should be maintained between 300-500kpa, and the oil inlet pressure of supercharger should not be lower than 80kPa when the engine is idling;
3.發動機啟動后，注意觀察增壓器進油口壓力，3秒內必須有壓力顯示。否則增壓器因缺少潤滑油而燒壞;
3. After the engine is started, pay attention to observe the pressure at the oil inlet of the supercharger. There must be a pressure display within 3 seconds. Otherwise, the supercharger will burn out due to lack of lubricating oil;
4.增壓器渦輪殼為高溫部位，操作人員應注意避免高溫燙傷。
4. Turbocharger turbine shell is a high temperature part, so operators should pay attention to avoid high temperature scald.
5.調壓閥的調節，逆時針旋轉，壓力減小，順時針旋轉，壓力增大。
5. The adjustment of the pressure regulating valve, counter clockwise rotation, pressure decreases, clockwise rotation, pressure increases.

上一條：燃?xì)獍l(fā)電機組對室內設備有哪些要求？

下一條：煤礦瓦斯發電的三個階段有哪些？

新聞搜索
濟南濟柴環能燃?xì)獍l(fā)電設備有限公司

  • 服務熱線

    0531-62325028
    0531-69951266
首頁 - 新聞中心 > 公司新聞

瓦斯發電瓦斯發電機組增壓器事項介紹

在使用瓦斯發電機組時，要注意增壓器的使用情況：
When using gas generator set, attention should be paid to the usage of supercharger
增壓器在高速、高溫、下工作，渦輪進口溫度可高達650°左右，標定轉速27500r/min，使用中特別注意做好維護保養工作。
The turbocharger works at high speed, high temperature and low temperature. The turbine inlet temperature can reach about 650 ° and the rated speed is 27500r / min. special attention should be paid to the maintenance work in use.
1.新啟用或維修后的增壓器，裝機前應用手撥動轉子檢查轉子轉動情況，正常情況下，轉子應輕快、靈活、無卡滯和異常聲響;
1. For the supercharger after new use or maintenance, the rotor should be manually moved to check the rotation of the rotor before installation. Under normal conditions, the rotor should be light, flexible, free of stagnation and abnormal sound;
瓦斯發電機組
2.接好潤滑管路，保持潤滑油路暢通，采用浮動軸承，對潤滑油要求較高，正常工作時，機油壓力應保持在300-500kPa之間，發動機怠速時，增壓器的進油壓力應不低于80kPa;
2. Connect the lubricating pipeline, keep the lubricating oil pipeline unblocked, adopt floating bearing, and have higher requirements for lubricating oil. During normal operation, the oil pressure should be maintained between 300-500kpa, and the oil inlet pressure of supercharger should not be lower than 80kPa when the engine is idling;
3.發動機啟動后，注意觀察增壓器進油口壓力，3秒內必須有壓力顯示。否則增壓器因缺少潤滑油而燒壞;
3. After the engine is started, pay attention to observe the pressure at the oil inlet of the supercharger. There must be a pressure display within 3 seconds. Otherwise, the supercharger will burn out due to lack of lubricating oil;
4.增壓器渦輪殼為高溫部位，操作人員應注意避免高溫燙傷。
4. Turbocharger turbine shell is a high temperature part, so operators should pay attention to avoid high temperature scald.
5.調壓閥的調節，逆時針旋轉，壓力減小，順時針旋轉，壓力增大。
5. The adjustment of the pressure regulating valve, counter clockwise rotation, pressure decreases, clockwise rotation, pressure increases.